Steel building types · Container Covers

Container Covers: Steel Roof Kits for Shipping Containers

A container cover is an engineered steel roof kit that spans between two shipping containers you supply (sea cans or Conex boxes). The containers become the walls, and the cover creates a clear-span space between them, with no posts, beams or trusses in the way, for equipment, vehicles, storage or a workshop. Every kit is engineered for your site's snow and wind loads and comes with engineer stamped drawings for your permit.


How a container cover works

What Is a Shipping Container Cover?

A shipping container cover is a steel roof that spans the gap between two shipping containers, turning them into a covered workshop, storage building or equipment shelter. The containers act as the walls, and the steel arch roof bolts on top, so you get a large, sheltered work area at a fraction of the cost of a full building. Toro container covers fit standard 20 ft and 40 ft containers. Base bolt holes are standard, and mounting plates are available on the R Model. Every cover is engineered for the snow, wind and seismic loads at your site and ships with stamped drawings for your permit. Pricing starts at $19 per sq ft (USD) or $26 per sq ft (CAD) and is quoted to make sure it meets the loads and codes for your location and use. Get a quote for your container setup.

Two Containers. One Roof.
Instant Covered Space.

Set two shipping containers on level ground, square to each other and spaced to the width you want covered. The steel roof bolts to the tops of the containers, and the containers carry the roof's weight down to the ground. You get instant covered space: a garage, equipment shelter, storage yard, workshop or commercial work area. Add end walls and doors and it becomes a fully enclosed building. See the three step process below.

  1. 1
    Tell us about your site and containers
    Where you’re located, your container sizes (for example 20 ft or 40 ft, standard or high cube) and the gap you want covered. We’ll see what’s required and help you design it to your needs, in a large variety of colors.
  2. 2
    We engineer, manufacture and ship it
    Your cover is designed for your local snow, wind and seismic loads. It comes with engineer-stamped drawings and the structural reactions for your containers and foundation, to help ensure compliance with local codes.
  3. 3
    Bolt it together
    The kit arrives with an assembly manual. Build it yourself or hire a local contractor to help. Smaller container covers go up with minimal manpower and equipment.
  • Straight-Wall

  • Arch-Style

  • Inside Mount

  • OUTSIDE Mount

Container Covers

Straight-wall, inside mount: the pitched roof covers only the gap between your containers and leaves their tops open.


Two Rooflines

straight-wall or arch-style (Quonset Hut) container covers

Both styles come in any length and can mount inside or outside your containers. Choose by what you'll store and how much height you need.

Large Outside Mount Steel Container Cover

Profile 01

Straight-wall

Container Covers

A cold-formed steel frame with a pitched roof, giving you more usable height across the full width for tall equipment, trucks and racking. Three mount styles: inside mount, inside mount with lean-tos, and outside mount. All available in a wide variety of colors.

  • Cold-formed or red iron framing
  • Single bay to wide clear-span
  • Ideal for long RVs, trailers and boats
Container Covers

Profile 02

Arch -Style (Quonset Hut)

Container Covers

A self-supporting curved steel roof with no frame. The arch sheds snow and carries load efficiently, so it's the strongest choice for wide spans and heavy snow areas. Made by our sister company Future Buildings and backed by a 50-year rust-perforation warranty.

  • Self-supporting arch roofline
  • Galvalume Plus® steel
  • Ideal for long RVs, trailers and boats

Straight-wall · Video

See the M-Model
Container Cover

Toro’s cold-formed straight-wall container cover, with a pitched roof that gives you more usable height across the full width for tall equipment, trucks and racking.

3D Builder

Customize Everything With Our 3D Builder

Width, length, height, color, lean-tos, mezzanines, openings and more. Design your perfect carport down to the smallest detail — super easy, no experience needed.

Color my building

Pick Your Colors

Panel
Trim
Panel Frame

Sizes

Container cover sizes: 20 to 80 feet wide and any length

Container covers are sized by the gap between your containers. We make them from 20 feet wide and above and they can come in any length: cover one pair of 20 ft or 40 ft containers, or line up several pairs and join the kits end to end. Sized by the gap between your containers, in 5 ft steps.

  • 30 to 40 ft gap: tractors and farm machinery, RVs and boats, a workshop
  • 45 to 60 ft gap: combines, trucks, a covered commercial work yard
A toro Steel Building Container Cover being used to store snowmobiles and an RV
Container Covers
Container Covers

BUILT FOR YOUR SITE

Engineered for your snow
and wind loads

A container cover is open at the ends, so wind gets underneath the roof and pushes up while it also pulls from above. Snow drifts unevenly across an arch. That’s why every Toro container cover is engineered for your address: we look up your local snow, wind and seismic loads, design the roof and its connections to the National Building Code of Canada or the IBC, and send stamped drawings sealed by an engineer licensed where you’re building.

Your containers matter too

Container Covers

They carry the roof’s weight and the wind uplift down to the ground, so they need to be structurally sound, level and square. With used or mismatched containers, tell us their condition and we’ll account for it in the design.

how to assemble a container cover - watch this timelapse

Every kit ships with stamped drawings and a step-by-step assembly manual. Most customers build it themselves with a small crew; you can also hire a local contractor.

Container Covers

Watch: How to Install a 30x40 Container Cover
Arch-style timelapse

Get your permit

Submit the stamped drawings to your building department, and check zoning.

Prepare the base

Containers can sit on a gravel pad, concrete footings, piers or a slab, as long as it’s firm and won’t settle.

Place the containers

Set them level, square to each other and at the exact gap shown on your drawings.

Assemble the roof

Bolt the roof sections together following the assembly manual.

Fasten it to the containers

Attach the roof to the containers exactly as shown on your drawings.

Add the finishing pieces

End walls, doors, vents and skylights go always go on last.


Make it yours

Container cover add-ons

Every add-on is included in your engineering, so the drawings show the complete building.

  • Front and back end walls
  • Turbine vents and ventilation
  • Walk-in (man) doors
  • Overhead (shipping) doors
  • Skylights
  • Insulation

Straight from customers

Container Cover Gallery

Real Toro container covers on farms, job sites and commercial yards.

Straight from customers

What container cover customers say

My experience with Luke Collins was great. He was knowledgeable, responsive and worked with my every step of the way…

Aaron M.

Just put my garage up and I couldn’t be happier. Exceptional quality and exactly what we needed. My experience working…

Luca

Shout out to Toro Steel for getting our sea can covers for our site - have worked with Josh for…

Eric R.

My family worked with Toro for a container roof that we use at our farm and experience was smooth from…

Liz D.

I recently purchased a piece of property and wanted to use Connex boxes for storage, so I reached out to…

Luke P.

Steel container cover on two shipping containers with a tractor parked underneath

My sales rep did a fabulous job helping me get the correct design for my needs. I have my basic…

Mark D.

Steel container cover between two shipping containers sheltering a tractor and a pickup truck

Memphise worked with me from ordering and getting what I needed . To delivery. Helped get the payments in on…

Walt G.

Steel container cover roof spanning two shipping containers with a mountain view

Toro Buildings has been exceptional to work with from start to finish. Simon was gracious and always responsive to any…

Jill W.

Frequently Asked Questions

Toro Steel container cover Kits FAQs

Quick answers to the questions we hear most. Still unsure? Our building specialists are happy to help.

A container cover is an engineered steel roof kit that spans between two shipping containers. The containers act as the walls, and the cover creates a sheltered, open space between them for storage, workshops, parking and equipment.

No. Toro sells the roof system only. You supply the shipping containers, new or used, that the cover attaches to.

Any length, and from 20 ft wide in 5 ft steps, measured as the gap between your containers. You can also join several kits end to end.

No. They can sit on gravel, concrete footings, piers or a slab, as long as the base is firm, the containers are level and square to each other, and they won't shift over time.

Yes. Line up as many pairs of containers as you need and join the kits end to end, or order one cover in the full length.

Steel doesn't burn, so a steel cover won't add fuel to a fire, which makes it a good choice for protecting equipment and inventory in wildfire areas.


Keep exploring

Related building types

Compare container covers with other Toro building types.

Join 85,000+ customers who built with Toro

Tell us your size, location and how you'll use the building. A Toro building consultant will come back with an engineered, code-compliant quote within 1 business day. Prefer to talk? Call 1-888-995-3432, or browse in-stock clearance buildings at reduced prices.

This site is registered on wpml.org as a development site. Switch to a production site key to remove this banner.